Objectives
This post is intended to help you get started with Scala Programming on NetBeans IDE in 15 minutes.
For demonstration purposes I am using
· Ubuntu Linux 14.04 though commands will be the same in any other Unix / Linux flavor
· Scala 2.105 (Apache Spark distribution) though commands will be the same in other lower / higher scala versions
· JDK 1.7 u80 64-Bit. Scala 2.10.5 requires JDK 1.6 or higher. Make sure you have the appropriate JDK pre-installed on your machine. Installation of JDK is out of scope for this post
Steps
1) Go to any directory on your machine (I use my home directory /home/admnistrator) and type the command
scala –version
You will see the following message which indicates that scala is not installed on your machine.
2) To download Scala 2.10.5 go to your browser and paste the following URL. Scala download page will show up.
http://www.scala-lang.org/download/2.10.5.html
Click the button “Scala 2.10.5” to download Scala binaries. The downloaded file has the name scala-2.10.5.tgz which is a compressed file.
I am using the Linux user “administrator” that was created while installing Ubuntu. Hence, the file got downloaded to /home/administrator/Downloads on my machine.
3) Extract this file using the following command
tar -xvzf scala-2.10.5.tgz
4) Once the extract is complete you will see the folder “scala-2.10.5” under /home/administrator/Downloads. Folders are in blue in the below screenshot.
5) To make this folder available to all users move it to /usr/local/ with the following command. You will need sudo privileges to move this folder to /usr/local/. This is because /usr/local/ is owned by root and not your userid.
sudo mv scala-2.10.5 /usr/local/
You will be prompted for sudo password. Go ahead and enter it.
Note – if there are organizational restrictions that do not allow you to move anything to /usr/local/ then just move this folder to your home directory using the below command. If you copy the scala folder to your home directory, be sure to set the environment variables described in later steps to refer to this location and NOT /usr/local/
mv scala-2.10.5 /home/<your_user>/
6) Go to the destination directory and verify that folder “scala-2.10.5” has execute permissions. This can be done by the command
ls –ltr
If you do not see “rwx” for your user on the scala folder assign permissions as follows
chmod –R 755 scala-2.10.5
This will give your userid full permissions (read, write, execute) and others (read, execute) permissions on the folder “scala-2.10.5”.
Final permissions should look like the following:
7) Next, set environment variables in .bashrc file. You can use any compatible editor available on your machine (vim, nano, etc.). I like nano editor better because it is easier to use.
Open .bashrc file in nano editor using the following command
nano ~/.bashrc
Add entries for environment variables SCALA_HOME and PATH using the following commands:
export SCALA_HOME=/usr/local/scala-2.10.5
export PATH=$PATH:$SCALA_HOME/bin
Ignore the other entries in my screenshot below as they are not meant for this installation
8) Press Ctrl+X to save your changes. At the below question enter “y”.
9) The system will prompt you for a filename as seen in the below screenshot. DO NOT enter another file name as it will result in the .bashrc file getting replaced with the new filename.
Just press ENTER to complete saving the file.
10) To populate Linux environment variables after adding your entries, execute the .bashrc file again using the following command:
source ~/.bashrc
Restarting your machine will also execute the .bashrc file again though you do not need to do it.
11) Check whether your SCALA_HOME variable got updated, using the following command:
echo $SCALA_HOME
This should output the value of SCALA_HOME variable as seen below:
12) Also check if the system is ready to use Scala by going to any directory on your machine and just typing “scala”
For e.g.
$cd /home/administrator
$scala
Scala prompt should show up as follows:
13) Check the scala version on your machine with the following command:
scala –version
The output of this command will show you the scala version you just installed as seen in the below screenshot
Scala is now setup successfully on your machine.
14) Open NetBeans IDE on your machine and go to ToolsàPlugins as shown below
15) Go to Available Plugins tab
16) On the right hand side, enter “scala” in the search text box and press ENTER. You will then see the list of scala plugin libraries available
17) Select all libraries that appear in the search results and click Install
18) In the next dialog box, click Next
19) Accept the License Agreement and click Install
20) In the below certificate warning, click Continue
21) Click Finish when the installation completes successfully. Scala plugins are now installed.
22) To start coding, go to the main page on NetBeans IDE and select FileàNew Project. The New Project window appears. Select the category and project as seen in the below screenshot
Category: Scala
Project: Scala Sbt Project
Click Next
23) Enter a Project Name for your project, e.g.ScalaProject. You can leave the Project Location and Project Folder unchanged or set them to where you want to your project and folder to reside on the system. Click Finish
24) Your project will get created as follows. Observe all sbt dependencies getting downloaded, the log for which is displayed in the bottom white area. Let this process complete.
Note – make sure you have an internet connection at this time
25) To start writing Scala code, go to FileàNew File on NetBeans IDE main page as seen below. Select the appropriate Category (Scala) and File Type (Class, Object, Main Object, etc.) and click Next.
That’s it you’re all set! Code away to glory……
Now read .... Access HDFS In Spark
